Main Page
From vvvA
anvilhead project
Consumers of the quality of shoes is very concerned about, but to no avail when purchasing shoes. The quality of shoes good or bad, there are shoe quality, manufacturing process quality, design the structure of shoes, apparel logistic problems comfortable wearing, shoes, etc. The function of many factors.
1. Shoe uppers and shoes, including the quality of in two parts, should be to identify the authenticity of the leather
Natural leather is leather, there are pores, and in general it is difficult to see by eye, the thumb pressing surface can be used to see whether there is next to the thumb as well as patterns of dermatoglyphics. Patterns have detailed, open hand after the disappearance of fine lines, flexible shoes good surface Fengman natural leather for a better, more deeper wrinkles is a natural skin inferior cortex. The absence of small lines, you are not a natural leather skin, including leather, including the second floor of a shave film. Natural leather, another distinctive feature is flawed skin surface. Natural leather uppers in general, in the inside of shoes and other inconspicuous places, there are a few minor flaws, such as dermatoglyphics uneven thickness, light boil, boil, such as lice. Cross-section of natural leather, there are three different density levels: a very fine flexible epidermis, the middle of dense dermis, below the meat is a relatively loose surface fiber layer, and layer with no obvious boundaries between layers. The shoe leather is an extension in order to prevent deformation and to improve the use of touch the reinforcement material. Requirements of shoe with a delicate touch materials, breathable, moisture good, and can not color performance. High-end shoes in the shoe, are the production of natural leather and cotton. If the uppers are natural leather, shoe leather alternative that is man-made, can only be regarded as middle and low shoes. Most consumers overlook the material on the shoe selection and identification, this is wrong. easternjordan.com wholesale sports shoes
2. View the upper suture and adhesive joints at the end help to identify the quality of the production process to see if there are disconnected, whether the upper suture neatly norms. In particular to help at the end of shoe adhesive binding site, it should be no adhesion formation, non-empty open seam and plastic signs.
3. Hand-to-lumen shoes, look at shoes at the end of the inside and inside, whether there is any contact with surfaces where the foot can not be uneven, or feet will blister. Shoes must have soles, it is to keep shoes clean and covered with nails at the end of the uneven eyes, a touch to improve the foot of the word.
4. Heel upper hand pick sites to see if stiffness and flexibility requirements of the site can not be followed by stiffness traces below the ankle flexibility good, not perfect, or ankle injury.
5. Push back when the Department at the end of the period to see if the internal hard shoes is the shoes at the end of the trunk and the frame, when in force at the end of compression in order to better. Skeleton and trunk stiffness is not, shoes will inevitably shape deformation, damage foot.
6. To be placed at random shoes on the desktop or on the glass to see whether the shoes when the shoes were a smooth release in the desktop, we should immediately stop sloshing around. quality shoes china
7. Fingertip with the middle finger to insert the following before the soles pointed to see a high degree of suitability of the former Organization of Alice when the first middle finger just enough belly thickness, indicating that the former Rocker is right. Rocker the former is too large, the steady reduction; than an hour before the Organization, in charge of wear shoes, shoes easily deformed foot fatigue.
8. With his hands to hold shoes, soles and heels to see whether contact with a smooth sole and heel will be light on the table (or counter) side, so that the side of shoes up to see the sole access to the site. To hold shoes (soles widest point) and the heel side plane contact with the table for good. Otherwise, deformation and easy to swap shoes heel. easternjordan.com cheap brand shoes
9. The shoe flat on the desktop, from two directions before and after to see if the correct head start with shoes, the soles look both inside and outside the edge of the size of tilt away from the desktop, it should be little difference in order to maintain consistency for a good balance. Further forward from the heel shoes, heel shoes, check whether the vertical up and down, not to the medial or lateral tilt as well.
10. With the index finger to help put up in a shallow outside help after the shoes to see a high degree of lateral upper part of the index finger down the inside of shoes at the end of contact, so that the index finger near the outside of the upper ankle to see the index finger knuckle of the second line, whether height of the upper lateral line. Shoes in general life, social etiquette shoes, shoes, slightly lower than the index finger to the second knuckle for a good line; sports shoes and casual shoes were missing after the soft mouth to help structure the lateral malleolus can be slightly higher to help high index finger knuckle in the second line.
11. Looking down from the upper down to see the symmetry of upper parts, as well as whether the outline of shoes I and heel deformation to the straight line between the midpoint of the axis of symmetry to see whether the parts on the uppers symmetry within symmetric, mutually moved backwards not forward for a good bit. Contour line of shoes I should have shoes together North Korea, smooth smoother for good; twisted into a lotus leaf-shaped shoes for the poor.
12. Understanding of the outside of shoes at the end of the performance, choose the applicable outside the clogs at the end of a variety of things, according to the main raw material can be divided into the rubber at the end of the end of imitation leather, plastic, etc. at the end of each performance are: rubber soles with soft, flexible, and anti-skid, wear-resistant, heat-resistant and good cold resistance. Texture is a bit heavier. Imitation leather soles, lightweight, stiffness, wear-resistant, resistant to twists and turns. However, less flexible, less non-slip. Plastic soles, wear-resistant, good flexibility. But the texture of hard, heat-resistant low cold resistance.
